价格:联系起
华北航天特种焊接材料有限公司
联系人:董胜彪
电话:15030898302
地址:河北邢台高新科技开发区1号
产品规格:齐全
产品数量:
包装说明:
关 键 词:A202
行 业:
发布时间:2012-05-03
A002 符合 GB E308L-16. 相当 AWS E308L-16 说明: A002是钛钙型药皮的**低碳Cr19Ni10不锈钢焊条。其熔敷金属含碳量≤0.04%,有很好的抗晶间腐蚀性能、良好的焊接工艺性能,药皮耐红,强度好,抗气孔性好。可交直流两用。 用途: 用于焊接**低碳Cr19Ni10不锈钢结构,也可用于0Cr19Ni11Ti工作温度低于300℃耐腐蚀的不锈钢结构,主要用于合成纤维、化肥、石油等设备的制造。 熔敷金属化学成分(%) 化学成分 C Mn Si S P Cu Ni Mo Cr 保证值 ≤0.04 0.5~2.5 ≤0.90 ≤0.030 ≤0.040 ≤0.75 9.0~11.0 ≤0.75 18.0~21.0 熔敷金属力学性能 试验项目 σb(MPa) δ5(%) 保证值 ≥520 ≥35 参考电流 (AC、DC+) 焊条直径(mm) φ2.0 φ2.5 φ3.2 φ4.0 φ5.0 焊接电流(A) 40~80 50~100 70~130 100~160 140~200 注意事项: 1.焊前焊条须经200-250℃烘焙1h。 2.尽可能采用直流电源,电流不宜过大。 A022 符合 GB E316L-16 相当 AWS E316L-16 说明: A022是钛钙型药皮的**低碳Cr18Ni12Mo2不锈钢焊条,其熔敷金属含碳量≤0.04%,具有良好的耐热、耐腐蚀及抗裂、抗气孔性能,有良好的操作工艺性能,药皮耐红,强度好。可交直流两用。 用途: 用于焊接尿素、合成纤维等设备及相同类型的不锈钢结构,也可用于焊后不能进行热处理的铬不锈钢及复合钢、异种钢等。 熔敷金属化学成分(%) 化学成分 C Mn Si S P Cu Ni Mo Cr 保证值 ≤0.04 0.5~2.5 ≤0.90 ≤0.030 ≤0.040 ≤0.75 11.0~14.0 2.00~3.00 17.0~20.0 熔敷金属力学性能 试验项目 σb(MPa) δ5(%) 保证值 ≥490 ≥30 参考电流 (AC、DC+) 焊条直径(mm) φ2.0 φ2.5 φ3.2 φ4.0 φ5.0 焊接电流(A) 40~80 50~100 70~130 100~160 140~200 注意事项: 1.焊前焊条须经200-250℃烘焙1h。 2.尽可能采用直流电源,电流不宜过大。 A022Mo 符合 GB E317L-16 相当 AWS E317L-16 说明: A022Mo是钛钙型药皮的**低碳Cr18Ni12Mo3不锈钢焊条,其熔敷金属含碳量≤0.04%,具有良好的耐热、耐腐蚀及抗裂、抗气孔性能,尤其耐腐蚀性能优于A022,有良好的操作工艺性能,药皮耐红,强度好。可交直流两用。 用途: 用于**低碳00Cr18Ni12Mo3不锈钢,也可用于焊后不能进行热处理的铬不锈钢及复合钢和异种钢的焊接。 熔敷金属化学成分(%) 化学成分 C Mn Si S P Cu Ni Mo Cr 保证值 ≤0.04 0.5~2.5 ≤0.90 ≤0.030 ≤0.040 ≤0.75 12.0~14.0 3.00~4.00 18.0~21.0 熔敷金属力学性能 试验项目 σb(MPa) δ5(%) 保证值 ≥520 ≥25 参考电流 (AC、DC+) 焊条直径(mm) φ2.0 φ2.5 φ3.2 φ4.0 φ5.0 焊接电流(A) 40~80 50~100 70~130 100~160 140~200 注意事项: 1.焊前焊条须经200-250℃烘焙1h。 2.尽可能采用直流电源,电流不宜过大。 A032 符合 GB E317MoCuL-16 说明: A032是钛钙型药皮的**低碳Cr19Ni13Mo2Cu不锈钢焊条,具有良好的耐热、耐腐蚀及抗裂、抗气孔性能,有优良的焊接工艺性能。可交直流两用。 用途: 由于焊缝中含有Mo和Cu,在硫酸介质中具有较高的抗腐蚀性能,用于焊接合成纤维等设备在稀、中浓度硫酸介质中工作的同类型低碳不锈钢结构,也可焊接Cr10Si3耐酸钢。 熔敷金属化学成分(%) 化学成分 C Mn Si S P Cu Ni Mo Cr 保证值 ≤0.04 0.5~2.5 ≤0.90 ≤0.030 ≤0.035 ≤2.0 12.0~14.0 2.00~2.50 18.0~21.0 熔敷金属力学性能 试验项目 σb(MPa) δ5(%) 保证值 ≥540 ≥25 参考电流 (AC、DC+) 焊条直径(mm) φ2.0 φ2.5 φ3.2 φ4.0 φ5.0 焊接电流(A) 40~80 50~100 70~130 100~160 140~200 注意事项: 1.焊前焊条须经200-250℃烘焙1h。 2.尽可能采用直流电源,电流不宜过大